Last Updated: November 17, 2026
The featured image is an AI-generated illustration of two of the products discussed, not a photo of units we handled. We did not physically test them. Appearance, colors and scale may vary.
Makers’ official sizing guides and size charts checked November 10, 2026. We did not test these pet doors; we compared published specs from each maker’s own pages.
AI disclosure: BestPetPicker Research prepared this page with AI assistance and checked each fact against the maker pages listed under Sources.
Dog door makers do not all measure a dog the same way, and a size called Medium does not mean the same opening from one maker to the next. This guide lines up four makers’ own sizing instructions and size charts: PetSafe, Ideal Pet, Endura Flap, and Hale Pet Door. It shows which measurement each one asks for, what their size names cover, where one maker’s own numbers disagree, and the short calculation that ties your dog’s measurements to a flap size and a mounting height.
Short answers
- Take two height measurements, not one. PetSafe and Ideal Pet ask for your dog’s body depth (top of the shoulders or back down to the bottom of the chest), which sets how tall the flap opening must be. Endura Flap and Hale ask for the height from the floor to the top of the shoulders or back, which sets how high the top of the flap must sit.
- Width: PetSafe and Hale both say to measure the widest point and add an inch or two. Ideal Pet measures across the shoulder, and Endura Flap measures a door opening your dog can walk through.
- Size names do not line up by weight. A 40 lb dog is at the top of PetSafe’s Medium (up to 40 lb), inside Ideal Pet’s Large (36 to 90 lb), and inside both Hale’s Tall Medium (30 to 45 lb) and Large (40 to 55 lb). Measure your dog rather than going by the size name.
- One maker, two sets of numbers: PetSafe’s size chart PDF lists a Medium flap of 8 1/4 × 11 1/4 in, while its Plastic Pet Door page lists 8 1/4 × 12 1/4 in and its Extreme Weather Pet Door page lists 8 1/8 × 12 1/4 in. Endura Flap’s two tables give different height figures for the same sizes. Check the page for the exact door you plan to buy.
- The check (our arithmetic from Endura Flap’s guide): step-over + flap height should be at least your dog’s floor-to-top-of-back height + 1 in, and Endura Flap says the step-over should be no more than one third of the height at the withers. With more than one dog, Hale says the door should be low enough for the shortest dog to step over and tall enough for the tallest to fit through.
How each maker measures height
| Maker | What the maker says to measure | What that number sets |
|---|---|---|
| PetSafe (size chart PDF) | “Measure your pet from the top of the shoulders to the bottom of the chest or belly, whichever is the tallest part. Add one or two inches.” | Flap opening height |
| Ideal Pet | “(B) Measure from the top of your pet’s back (just behind their head) to the bottom of chest.” | Flap opening height |
| Endura Flap | “measure from the floor to the tallest point of your dog’s back (this may be their shoulders, mid-back, or tailbone).” | Height of the top of the flap above the floor |
| Hale Pet Door | “To get this height, measure your pet from the withers (top of the shoulders) to the floor.” | Height of the top of the flap above the floor |
The first two measurements tell you whether your dog fits through the opening. The second two tell you whether the opening sits high enough once the door is installed. Hale puts it this way: “The pet door flaps should be at least an inch or two above the top of your pet’s back, not the head.” Hale also notes, “Remember that your door won’t be placed completely at floor level.” PetSafe’s body-depth method appears under the heading “Pet Doors without a predetermined rise”, and the PDF adds, “Remember to allow for your pet’s future growth.”
For width, PetSafe says, “Measure the widest part of your pet, the chest or hips. Add one or two inches.” Hale says, “Simply measure your pet at the widest point and add an inch or two for safety.” Ideal Pet says, “(A) Measure the widest point of your pet’s shoulder.” Endura Flap uses a door instead of a tape on the dog: “Open your door or sliding glass door as wide as your pet needs to walk through comfortably.” Then, “Measure the width of the opening you have made.”
Flap sizes in each maker’s chart
All figures are in inches, width × height, copied from each maker’s page. Weight ranges are the makers’ own. For prices, check each maker’s page for the size you need.
PetSafe Plastic Pet Door
| Size | Maker’s pet weight | Flap opening |
|---|---|---|
| Small | Up to 15 lb | 5 1/4 × 8 1/8 |
| Medium | Up to 40 lb | 8 1/4 × 12 1/4 |
| Large | Up to 100 lb | 10 1/4 × 16 1/4 |
| Extra Large | Up to 220 lb | 13 3/4 × 23 3/4 |
PetSafe says it “fits interior or exterior doors made of wood, PVC, metal or paneling” and lists “Fits doors 1/16 inches–2 inches thick”. A cutting template comes in the box.
PetSafe Extreme Weather Pet Door
| Size (maker’s pet weight) | Flap opening | Cut-out |
|---|---|---|
| Small (up to 15 lb) | 5 1/8 × 8 1/4 | 6 3/8 × 10 1/8 |
| Medium (up to 40 lb) | 8 1/8 × 12 1/4 | 9 3/8 × 14 |
| Large (up to 100 lb) | 10 1/8 × 16 1/4 | 11 3/8 × 19 |
PetSafe lists this door for “standard-size paneled, wood, metal and PVC doors 1 5/8 in – 2 1/4 in thick”.
PetSafe size chart PDF (covers all PetSafe dog doors)
| Size | Maker’s pet weight | Flap opening |
|---|---|---|
| Small | 1 to 15 lb | 5 1/4 × 7 1/2 |
| Medium | 1 to 40 lb | 8 1/4 × 11 1/4 |
| Large | 1 to 100 lb | 10 3/8 × 15 3/8 |
| X-Large | 12 to 220 lb | 13 5/8 × 23 5/8 |
PetSafe explains these PDF figures: “The flap opening sizes listed represent the smallest amount of usable, open space across all our dog doors.” It adds, “If your pet fits with these dimensions for a particular size, then you will be able to use that size in any style of our dog doors.” See the next section for where the product pages differ.
Ideal Pet Original Plastic Pet Door
| Size (maker’s pet weight) | Flap opening | Cut-out |
|---|---|---|
| Small (2 to 12 lb) | 5 × 7 | 6 1/4 × 9 1/2 |
| Medium (13 to 35 lb) | 7 × 11 1/4 | 8 1/4 × 13 1/2 |
| Large (36 to 90 lb) | 10 1/2 × 15 | 11 3/4 × 17 1/2 |
| Extra Large (91 to 120 lb) | 15 × 20 | 16 1/2 × 22 1/4 |
Ideal Pet lists this frame for doors 1 1/4 to 2 in thick. The size menu on the same page calls the largest size Super Large (“Super Large – 15″ x 20″ flap”); the table calls it Extra Large.
Ideal Pet Ruff-Weather Pet Door
| Size (maker’s pet weight) | Flap opening | Cut-out |
|---|---|---|
| Small (2 to 12 lb) | 5 × 9 1/4 | 6 1/2 × 11 1/4 |
| Medium (13 to 35 lb) | 7 1/4 × 13 | 8 3/8 × 15 |
| Large (36 to 90 lb) | 9 3/4 × 17 | 11 1/8 × 19 1/4 |
| Extra Large (91 to 120 lb) | 15 × 23 1/2 | 16 1/4 × 25 3/4 |
Ideal Pet says the frame “can be installed in doors ranging from 3/4″ to 1-3/4″ thick”. With the Ruff-Weather Wall Kit, which Ideal Pet lists as “purchased separately”, the door fits walls 4 3/4 to 7 1/4 in thick.
Endura Flap Door Mount Pet Door
| Size (maker’s minimum weight) | Flap opening | Rough cut-out |
|---|---|---|
| Small (10 lb) | 6 × 11 | 9 1/4 × 15 1/8 |
| Medium (20 lb) | 8 × 15 | 11 5/16 × 19 3/16 |
| Large (20 lb) | 10 × 19 | 13 3/8 × 23 3/16 |
| XL (30 lb) | 12 × 23 | 15 1/2 × 27 3/16 |
| XXL (50 lb) | 14 × 27 | 17 1/2 × 31 1/4 |
These rows come from the standard-door table on Endura Flap’s sizing page (“Example product used: Endura Flap Door Mount Pet Door”); the minimum weights come from the overview table on the same page. Endura Flap’s overview table gives a minimum weight for each size. It also says, “Endura Flap is not recommended for kittens or very small dogs.” For the door thickness this model fits, ask Endura Flap.
Hale Pet Door standard sizes
| Size (maker’s weight note) | Passage opening | Maker’s pet shoulder height |
|---|---|---|
| Small Medium (small cats up to 10 lb) | 6 1/2 × 9 1/2 | 9 to 13 |
| Tall Small Medium (small, tall dogs, 12 to 25 lb) | 6 1/2 × 12 1/2 | 12 to 15 |
| Medium (dogs 10 to 35 lb) | 8 1/2 × 12 1/2 | 12 to 15 |
| Tall Medium (tall dogs 30 to 45 lb) | 8 1/2 × 16 | 15 to 20 |
| Large (dogs 40 to 55 lb) | 11 × 16 | 15 to 20 |
| Tall Large (taller dogs 50 to 95 lb) | 11 × 19 1/2 | 21 to 24 |
| Tall Large Plus (tall, slender dogs up to 110 lb) | 11 × 23 1/2 | 25 to 27 |
| Extra Tall Large (very tall, slender dogs up to 120 lb) | 11 × 27 1/2 | 24 to 31 |
| Extra Large (large dogs up to 120 lb) | 14 × 19 1/2 | 22 to 24 |
| Extra Large Plus (larger dogs up to 150 lb) | 14 × 23 1/2 | 25 to 27 |
| Giant (most giant breeds) | 15 1/2 × 27 1/2 | 25 to 31 |
Hale says “we have 11 standard sizes”. Its chart also lists the rough opening, frame size, and pet width for each size.
Step-over: how high the door sits
Endura Flap defines it: “The distance from the ground to the bottom of the pet door flap is called the “step-over.”” Hale calls it the rise: “The rise is the lip at the bottom of the door that the pet must step over to use the door.”
- Hale: “Our standard rise on our product is 2 inches.” Hale adds, “This measurement is generally only applicable for wall installs above or through floorboards.” For its panels: “Panel models have a standard rise of 5″ but can be ordered with no rise.”
- Endura Flap Thermo Panel 3e (sliding-door panel): the step-over is adjustable. Endura Flap measures it as “The distance from the bottom of the panel to the bottom of your flap.” See the table below.
- Doors you cut into a house door (PetSafe, Ideal Pet, Endura Flap Door Mount): you set the step-over by where you cut the hole. Each maker’s cut-out is taller than its flap opening (PetSafe Extreme Weather Medium: 12 1/4 in tall flap, 14 in tall cut-out), so the bottom of the flap ends up a little above the bottom of the hole. Measure the step-over to the bottom of the flap, as Endura Flap defines it. PetSafe’s sizing PDF covers “Pet Doors without a predetermined rise”.
| Thermo Panel 3e size | Flap opening | Step-over range (as shipped) |
|---|---|---|
| Small | 6 × 11 | 3 to 4 1/2 (3) |
| Medium | 8 × 15 | 3 to 4 1/2 (3) |
| Large | 10 × 19 | 3 to 6 (4 1/2) |
| Extra Large | 12 × 23 | 3 to 6 (4 1/2) |
| XX Large | 14 × 27 | 3 to 7.5 (6) |
Endura Flap also points out, “Backyards and patios are typically a few inches lower than a home’s floor level.” Measure the step on the outside too.
The calculation
Endura Flap’s measuring guide says: “Adjust until you decide on a step-over height and dog door size that will allow at least 1″ above your pet’s withers.” Its checklist adds: “The top of the opening is at or above your pet’s withers, so they don’t have to crouch when they are using their door.” The top of the opening sits at the step-over plus the flap height, so in one line (our arithmetic, using the floor-to-top-of-back measurement Endura Flap asks for):
step-over + flap height ≥ floor-to-top-of-back height + 1 in
An earlier step in the same guide is worded differently: “Add the step-over height to the height of your pet measured earlier. The top of the flap should be mounted at least 1″ higher than this.” Read word for word, that asks for more height than the line above. If your dog is close to a size limit, ask Endura Flap which reading it means.
Endura Flap adds a limit on the step-over: “In no case should the step-over exceed 1/3 of the height at the withers – the lower the step-over, the better.” Hale’s version of the height rule asks for an inch or two of clearance (quoted above).
Worked example from Endura Flap’s own numbers (our arithmetic). The Thermo Panel 3e Large has a 19 in tall flap and ships with a 4 1/2 in step-over. That puts the top of the flap 23 1/2 in above the bottom of the panel. If the panel’s bottom is level with the floor your dog stands on, the line above fits a dog up to 22 1/2 in from the floor to the highest point of its back. The one-third rule says a 4 1/2 in step-over suits a dog at least 13 1/2 in tall at the withers. At the panel’s 6 in maximum step-over, the top of the flap is 25 in up, which fits a dog up to 24 in (all our arithmetic).
Endura Flap’s own table lists a recommended pet height of 9 to 27 in for this panel size. By our arithmetic, a dog taller than 24 in at the highest point of its back would need a step-over above the panel’s 6 in maximum to keep 1 in of clearance under the line above. Ask Endura Flap which figure to follow for a tall dog.
More than one dog
Hale: “If you have more than one pet, make sure you get a door that will work for all of them: low enough for the shortest one to step over but tall enough for the tallest one to fit through comfortably.” Endura Flap: “For pet owners with more than one pet, make sure that you do this with your widest and tallest pet so that the doggy door size you choose works for all your pets.”
Two-dog example (made-up dogs, our arithmetic). The shorter dog is 12 in at the withers, so the one-third rule caps the step-over at 4 in. The taller dog measures 24 in from the floor to the top of its back, so the top of the flap needs to be at least 25 in up. With a 4 in step-over, that means a flap at least 21 in tall. Then look for a flap height of 21 in or more in the tables above, wide enough for the wider dog.
Before you cut anything, Endura Flap suggests a cardboard test: “You can cut a hole in a piece of cardboard the same size as the pet door you want to buy.”
Where one maker’s numbers disagree
PetSafe: size chart PDF vs. product pages
| Size | Size chart PDF | Product pages |
|---|---|---|
| Small | 5 1/4 × 7 1/2 | Plastic: 5 1/4 × 8 1/8 Extreme Weather: 5 1/8 × 8 1/4 |
| Medium | 8 1/4 × 11 1/4 | Plastic: 8 1/4 × 12 1/4 Extreme Weather: 8 1/8 × 12 1/4 |
| Large | 10 3/8 × 15 3/8 | Plastic: 10 1/4 × 16 1/4 Extreme Weather: 10 1/8 × 16 1/4 |
The PDF calls its figures “the smallest amount of usable, open space across all our dog doors.” The product pages list taller openings, which fits that description, but some of their widths are narrower than the PDF’s: 8 1/8 in for the Extreme Weather Medium against the PDF’s 8 1/4 in, for example. If your dog’s width is close to a limit, ask PetSafe which width applies to the door you are buying.
Endura Flap: two height columns
| Size | Recommended pet height (standard-door table) | Max shoulder height (overview table) |
|---|---|---|
| Small | 8 to 14 | Up to 18 |
| Medium | 8 to 21 | Up to 22 |
| Large | 8 to 27 | Up to 27 |
| XL | 8 to 34 | Up to 31 |
| XXL | 8 to 41 | Up to 37 |
Both columns are on the same Endura Flap page. Run your own dog’s numbers through the calculation above, and ask Endura Flap if the result falls between the two figures.
If you are also sizing a crate, see our puppy crate guide.
Sources
- PetSafe (U.S. site): pet door size chart (PDF) · Plastic Pet Door · Extreme Weather Pet Door (checked November 10, 2026)
- Ideal Pet Products: Original Plastic Pet Door · Ruff-Weather Pet Door (checked November 10, 2026)
- Endura Flap: how to measure your pet · size charts for all Endura Flap doors (checked November 10, 2026)
- Hale Pet Door: dog door sizing guide (checked November 10, 2026)
We did not test these pet doors. Sizes come from each maker’s pages on the date shown and can change; check the maker’s page for your exact model and size before you cut a door or wall.